Latest E20-375 Dumps in VCE and PDF from PassLeader: https://www.passleader.com/e20-375.html (232 Q&As), welcome to download the latest DELL&EMC E20-375 exam dumps from PassLeader.com. PassLeader.com has the most valid E20-375 exam dumps, which will help you passing E20-375 exam easily! Both E20-375 VCE and PDF dumps are available now, 100% pass ensure.
Besides, you can download the latest PassLeader E20-375 Dumps online for FREE: https://drive.google.com/open?id=1aZ2kLYcJbpe1Kr5lhudnH5FI9gwgyV7S
QUESTION 61
After running a log collection, which user should you log in as to download the output file?
A. admin
B. monitor
C. boxmgmt
D. security-admin
Answer: A
QUESTION 62
Which protocol does the vRPA use to access the journal volumes?
A. iSCSI
B. FC
C. IP
D. FCoE
Answer: A
QUESTION 63
What would cause a volume sweep to occur?
A. A new Replication Set is added to an enabled Consistency Group.
B. A previously disabled splitter is enabled.
C. A Replication Set is removed from a disabled Consistency Group.
D. A previously enabled splitter is disabled.
Answer: A
QUESTION 64
A storage administrator is installing the VSI RecoverPoint Management plug-in, but the installation fails. What could be causing this?
A. vSphere client not installed.
B. vSphere client not running during the installation.
C. RPAs used were all virtual.
D. At least one virtual RPA present.
Answer: A
QUESTION 65
What occurs in a RecoverPoint system during a High Load event?
A. It keeps tracking I/O in marking mode.
B. It saves I/O in the production journal.
C. It saves I/O in the remote journal.
D. It does not track or journal I/O.
Answer: A
QUESTION 66
What are two requirements for an EMC RPA to connect to an EMC VNX via a SAN?
A. Each VNX SP needs to be connected to both fabrics.
At least two initiators per RPA need to be zoned to each SP.
B. Each VNX SP needs to be connected to both fabrics.
RPA HBA1 needs to be zoned to SPA and RPA HBA2 needs to be zoned to SPB.
C. Each VNX SP needs to be connected on a separate fabric.
At least two initiators per RPA need to be zoned to each SP.
D. Each VNX SP needs to be connected on a separate fabric.
RPA HBA1 needs to be zoned to SPA and RPA HBA2 needs to be zoned to SPB.
Answer: A
QUESTION 67
You are implementing a VPLEX 4-engine Metro with a RecoverPoint cluster at one site. You need to add all VPLEX splitters to the RecoverPoint cluster. How many splitters need to be registered?
A. 1
B. 2
C. 4
D. 8
Answer: A
QUESTION 68
An application team will be performing a major update to a RecoverPoint protected application. You have been asked by the application team for the best way to ensure a quick recovery at the remote cluster in case the update fails. In RecoverPoint, what should be done to the associated Consistency Group?
A. Manually create a bookmark prior to the update.
B. Enable logged access mode on the source.
C. Enable physical access on the target.
D. Use virtual access mode on the source.
Answer: A
QUESTION 69
A company recently acquired a new DR site and requires local Fibre Channel based production data to be replicated synchronously. They are investigating what infrastructure is needed on this DR site. What is an important connectivity consideration?
A. Site-to-site connectivity can be based on IP.
B. Site-to-site connectivity requires Fibre Channel.
C. Site-to-site connectivity requires FCIP.
D. Maximum synchronous replication speed is 400 MBps.
Answer: A
QUESTION 70
Which connectivity protocols are used to interconnect RecoverPoint clusters?
A. FC and IP
B. FC and iSCSI
C. FC and FCoE
D. FCoE and IP
Answer: A
QUESTION 71
When is the Open Replicator RecoverPoint session created for each replica volume in the Consistency Group (CG)?
A. CG is put into Image Access mode.
B. CG is created.
C. CG is enabled.
D. CG is taken out of Image Access mode.
Answer: A
QUESTION 72
Which Image Access Mode should be used when large portions of an image might be changed?
A. Logged Access
B. Virtual Access (without Roll)
C. Snap Access
D. Virtual Access (with Roll)
Answer: A
QUESTION 73
An administrator experiences a serious error with an RPA and calls EMC Support to resolve the issue. They are concerned that the system did not automatically notify EMC Support via the ESRS gateway. You check all settings in Unisphere Configure System Notification and find they are correct. What is the most likely cause for this notification failure?
A. TCP port 25 blocked at their firewall.
B. TCP port 989 blocked at their firewall.
C. TCP port 990 blocked at their firewall.
D. Temporary remote support license key expired.
Answer: A
QUESTION 74
An existing RecoverPoint/CL environment consists of one cluster at the main office and one off-site DR cluster. You have been asked to expand the environment to the maximum number of DR sites using RecoverPoint. How many additional clusters could be added to this RecoverPoint Environment?
A. 2
B. 3
C. 4
D. 5
Answer: B
QUESTION 75
You are a storage administrator tasked with creating a Consistency Group in a RecoverPoint/EX system. You launch the Protect Volumes wizard in Unisphere and notice that the desired production volume is not available. What would be a possible cause?
A. The production volumes are on a non-licensed array.
B. The volumes are masked to a host.
C. The journal volumes are on a non-licensed array.
D. Consistency Groups can only be created by boxmgmt.
Answer: A
QUESTION 76
A administrator wants to add a new RecoverPoint UserID. Which role must their UserID belong to in order to manage user settings?
A. security
B. admin
C. boxmgmt
D. monitor
Answer: D
QUESTION 77
What is the minimum number of RecoverPoint Clusters required to use the MetroPoint feature?
A. 1
B. 2
C. 3
D. 5
Answer: B
QUESTION 78
System events can be copied to the clipboard from which Unisphere for RecoverPoint view?
A. RecoverPoint Dashboard
B. Recovery
C. RPA Clusters
D. Admin
Answer: A
QUESTION 79
What would cause a volume sweep to occur?
A. A previously disabled volume is enabled.
B. A new Replication Set is added to a disabled Consistency Group.
C. A previously enabled splitter is disabled.
D. A Replication Set is removed from a disabled Consistency Group.
Answer: A
QUESTION 80
Which drop-down menu in Unisphere for RecoverPoint would you use to navigate to `Collect System Information’?
A. Admin
B. Event Logs
C. Dashboard
D. Support
Answer: A
Welcome to try PassLeader E20-375 VCE and PDF dumps: https://www.passleader.com/e20-375.html (232 Q&As)
Or, download more PassLeader E20-375 dumps for FREE: https://drive.google.com/open?id=1aZ2kLYcJbpe1Kr5lhudnH5FI9gwgyV7S